Guitar center launchcontrol xl3/27/2023 different "Endless" Mode for the Rotors and Sliders: So you must not switch through Banks or Presets to switch to any Mode, very faster to work with. Long_Press Bank: Pro Channel 1 Track Mode Long_Press Preset: Reset to Preset 1 Bank 1 This is the greatest Improvement for now:īrought all things together! Now all Modes are available from Preset 1 Bank 1: Up/Down/Left/right on Rotor 23 and 24 for faster working….Ĭ1, C#1, D1, E1, F1, F#1, G1,G#1, A1, A#1, B1 and C2 on the Buttons for to record Midi….(LEDs with different Colors)Īdded Last Changes document, cause nearly every time I work in Studio I find some things to add/change for better working with it! Snap Settings on Rotor, Note Length on Rotor, Zoom Hor at Now Time, Zoom Ver at Now Time, Zoom Ver/Hor at Data Cursor, Next/Prev Marker/Bar, Select Left/right, Move Data Cursor Left/Right/Up/down, Open PRV, Length of selected Note(s) +- 10 Ticks (Repeat of Key will come), Nudge Left/Right/Up/Down selected Note(s), Nudge Octave Up/down of selected Note(s), Next/Prev Note select,Note Velocity +- 1/5, Toggle Edit View, Do nothing, Snap to/By….more to come… Shows Level of selected Clip or Track on the Buttons (Green, Yellow, Red over -2 dB, Gain, Pan, Volume WAI Track 1-8, Move to Next/Previous Bar/Marker/Section, Select Clip Left/Right/Up/down, Zoom Ver/Hor, goto From/Thru, Select From/To Now Time, Reset WAI to Track 1/57, Loop On/Off, Set Loop to Selection, Show Arranger, Play Selection, Select Clip Left/Right/Up/Down on Buttons, Solo Selected Track, Select None, Selection +- 2 dB, CTRL+Z (Undo), Do nothing, Open Control Bar, Open Multidock, Fit Tracks Vertical, Fit Project, more to come……Īll Pro Channel Standard Parameter on Rotors, Sliders and Buttons! (See 1-TrPCMode.docx)Īll Pro Channel Standard Parameter of 8 Tracks simultaniously, Bank 1 Bass, Bank 2 LoMid Parameter, Bank 3 HiMid Parameter and Bank 4 Hi Parameter for 8 Tracks, for sure not to forget Compressor, Tube and Console Emulation 8 Tracks.ĩ6 Rotors, 32 Sliders and 64 Buttons for ACT, more with Shift on 4 Banks.Ģ4 Tracks Volume on Rotors, 24 Tracks Pan on Rotors with Shift, 8 Tracks WAI Bus Volume on Sliders and 8 Track Pan on Sliders, Mute and Solo for 8 WAI Buses. Same as in Normal Mode plus some Record specific commands and functions. Goto From, Select Active Track, Select None, Exit Cakewalk, Do Nothing (for some Rotors and Sliders), Open Control Bar/Multidock, Fit Project Ver/Hor, Select Clips Left/Right, Move Data Cursor Left/Right, with Shift Up/Down, Select in Timeline (snap), Narrow/Widen Selection, Move Selection, Zoom In on Selection, Audio Selection +- 2 dB(more to come) Moving to Bars, Markers, Sections, Next/Previous 8/1 Track(s), Zoom (Hor/Ver), Snap Settings on Rotor, Note Length on Rotor, Prev/Next TAB, Loop On/Off. SHIFT, CTRL, DOUBLE_PRESS and LONG_PRESS Buttons for additional possibilitiesĪll "Normal" Parameter, Gain, Pan, Volume, Send 1-6, Send 1-6 Pan, Solo, Mute, Inp. I use Userpresets 1-4 from LaunchControl XL MK II (Novation-2.0-LC_Preset 1-4.syx) and Preset „AZC - Nov-2.0-LC 01-27-2021.spp“ for AZControl 0.5r9 (newest release) Everything works as expected! Tested all Modes, all is fine! In the preferences->Midi->Instruments->Port/All Channels of the Controller->Define-> Import LaunchControlXL.ins (Download from OneDrive Link) Now this Controller is not resetted on Settings-> Project->More Midi->"Reset Controller when playback stop" enabled.Īlways the newest Files: Latest Version 10-05-2021 Important for not to reset Controller when playback stop.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |